What are the problems with the transducer of ultrasonic cleaning machine? Before using the instrument, it is necessary to understand one of the important accessories of the transducer ultrasonic cleaning machine. In the process of use, only when the transducer works normally can it have better cleaning effect. Once the transducer fails in the process of use, it will affect the cleaning function of the whole ultrasonic cleaning machine. What are the common failures of the transducer?

超聲波清洗機常見故障一：換能器常見故障之受潮

Common faults of ultrasonic cleaning machine 1: common faults of transducer affected with damp

檢測換能器是否受潮，只需要用兆歐表檢查換能器的絕緣電阻即可，如果電阻值達不到要求，那么可以肯定的就是換能器受潮。解決方法：將整個換能器（噴塑外殼除外）放到烘箱中，以一百度左右的高溫烘三個小時以上，直到用兆歐表檢測時絕緣電阻能夠達到要求為止。

To detect whether the transducer is damped, we only need to use a megohmmeter to check the insulation resistance of the transducer. If the resistance value does not meet the requirements, it is certain that the transducer is damped. Solution: put the whole transducer (except the plastic shell) into the oven and bake it at a high temperature of about 100 ℃ for more than three hours until the insulation resistance can meet the requirements when using the megohmmeter.

二：能器常見故障之振子打火和脫膠

2： Vibrator ignition and degumming

發現振子出現打火同時伴有陶瓷材料破碎的情況，這時就會影響振動面的振動效果，不及時處理會燒壞振子。遇到這種情況應該找技術人員來分別檢查下，將損壞的振子斷開，以免影響到其他振子的正常使用。然后將損壞的振子返回廠家維修。

It is found that when the vibrator ignites and the ceramic material is broken, the vibration effect of the vibrating surface will be affected, and the vibrator will be burnt if it is not handled in time. In this case, we should find technical personnel to check and disconnect the damaged vibrator, so as not to affect the normal use of other vibrators. Then return the damaged vibrator to the manufacturer for repair.

三：不銹鋼振動面穿孔

3： Stainless steel vibration surface perforation

如果超聲波清洗劑的換能器滿負荷使用時間太長就有可能出現振動面穿孔的情況，這是由于振動面的不銹鋼板長時間高頻振動疲勞所致，好的解決方法就是采購型號一樣的振動面進行更換

If the transducer of ultrasonic cleaning agent is used at full load for a long time, the vibration surface may be perforated. This is due to the high frequency vibration fatigue of stainless steel plate on the vibration surface for a long time. A good solution is to purchase the same type of vibration surface for replacement